-20%

Edwards nEXT300D Compound Turbomolecular Vacuum Pump, 300 l/s, CF 6 inch Inlet, 160 Watts, B82200200


  • MASS SPECTROMETRY: GCMS, LCMS, ICPMS,MALDI inorganic MS, RGA, surface science,leak detectors
  • WHERE nEXT IS FITTED: TEM, SEM, SPM,sample prep benches
  • RESEARCH & DEVEL OPMENT: Chamber evacuation, coating systems, turbopump systems
  • HIGH ENERGY PHYSICS: Beam Lines, accelerators, mobile pump carts, turbopump backing, laser evacuation, medical systems
  • SERIAL COMMUNICATION CONTROL: available with RS323 and RS485 (Windows softwar eincluded)
  • INDUSTRIAL: Glove boxes, coating systems, XRD/XRF systems, lamp evacuation
  • SEMICONDUCTOR: Load locks and transfer chambers
  • SOLAR: Photovoltaics, solar thermal technology

$11,639.75 $14,549.69

Compare

This listing is for the new Edwards nEXT-300D hybrid bearing compound turbomolecular vacuum pumps, operates on 24 to 48 VDC, 160 Watt version, for use with 100 or 200 Watt TIC controllers, reduced start up time to full speed, pumping speed of 300 liters per second (l/s) of nitrogen, CF Conflat 6 inch inlet flange, ISO KF-25 exhaust foreline flange, pump to controller cable attached (1 meter) with Edwards part number B822-00-200. A basic pump system would require a Edwards nEXT300D pump, a TAG or TIC controller, either an air or water cooling accessory and a suitable backing roughing pump. The complete specifications and application brochure in PDF format can be downloaded below.

The Edwards nEXT300D is a hybrid bearing compound turbo pump and available with either ISO-100 or Conflat 6 inch inlet flanges and have a pumping speed of 300 l/s of nitrogen. The nEXT pumps combine Edward’s proven bearing technology (oil lubricated ceramic lower bearing with dry permanent magnetic upper bearing), with improved rotor design and a new molecular drag stage to deliver improved pumping speeds, compression ratios, and true user serviceability. They feature 24 to 48 VDC sensor less motors with a built in drive that is fully compatible with the range of TAG and 100W and 200W TIC controllers. They are available pre-set for either 80W or 160W maximum power, the 80W pumps can be used with the Edwards 100W TIC controllers for low power applications but will require a longer ramp time to full operating speed.

User Friendly Maintenance Technology
The new Edwards nEXT technology have enabled the pumps to be serviced in the field. An interim oil lubrication change can be performed, where access allows, in-situ, typically in less than 5 minutes with the minimum of specialist tooling. A bearing and oil lubrication service, with minimum disassembly can be performed in less than 10 minutes using basic workshop tools and an Edwards tool kit. The nEXT pumps will advise the user when a service is due and what level of intervention is required. The request for service is by a simple flashing LED sequence on the pumps, and by serial communication notification.

Category:
Parameter nEXT300D IS0100 nEXT300D CF100 nEXT300T IS0100 nEXT300T CF100
Mass 5.7 kg 8.5 kg 6 kg 8.8 kg
Inlet flange DN100ISO-K DN100CF DN100ISO-K DN100CF
Outlet flange DN25NW DN25NW DN25NW DN25NW
Vent port 1/8 inch BSPP 1/8 inch BSPP 1/8 inch BSPP 1/8 inch BSPP
Purge port 1/8 inch BSPP 1/8 inch BSPP 1/8 inch BSPP 1/8 inch BSPP
Interstage port DN25NW DN25NW DN25NW DN25NW
Booster port DN25NW DN25NW DN25NW DN25NW
Inlet pumping speed
N2 300 l/s 300 l/s 300 l/s 300 l/s
He 340 l/s 340 l/s 340 l/s 340 l/s
H2 280 l/s 280 l/s 280 l/s 280 l/s
Inlet compression ratio
N2 >1 x  10 11 >1 x  10 11 >1 x  10 11 >1 x  10 11
He 1 x 10 6 1 x 10 6 3 x 10 6 3 x 10 6
H2 5 x  10 4 5 x  10 4 1 x  10 4 1 x  10 4
Interstage pumping speed
N2 13 l/s 13 l/s 13 l/s 13 l/s
He 13 l/s 13 l/s 13 l/s 13 l/s
H2 11 l/s 11 l/s 11 l/s 11 l/s
Peak booster
Pumping speed (nitrogen)
RV12 backing pump 26 m3h-1 26 m3h-1
XDS10 backing pump 24 m3h-1 24 m3h-1
Ultimate pressure <6 x 10-8 mbar <5 x 10-10 mbar <6 x 10-8 mbar <5 x 10-10 mbar